iHome Speaker System iDM8 User Manual

iDM8  
portable rechargeable  
Bluetooth speaker  
instruction manual  
 
iDM8  
Introduction  
Thank you for purchasing the iHome iDM8. This product is designed to provide high quality wireless  
sound for your iPad, iPhone, iPod, computer, PDA or other Bluetooth audio device.  
Along with the included Quick Bluetooth Connection Guide this instruction booklet explains the basic  
operation and care of the unit. Please read them carefully and keep for future reference.  
Maintenance  
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.  
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other  
protective material should be placed between it and the furniture.  
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents,  
such as benzene, thinner or similar materials can damage the surface of the unit.  
is a registered trademark of SRS Labs, Inc. TruBass technology is incorporated under license  
from SRS Labs, Inc.  
SRS W O W ® , which features TruBass® , significantly im proves the playback quality of audio, delivering  
a dynamic 3D entertainment experience with deep, rich bass and high frequency clarity for crisp detail.  
 
iDM8  
FCC Information  
FCC ID: EMOIDM8  
IC: 986B-IDM8  
FCC Radiation Exposure Statement  
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be  
co-located or operating in conjunction with any other antenna or transmitter.  
This Device complies with RSS-102 of the IC Rules; Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference and  
(2) This device must accept any interference received, including interference that may cause undesired operation.  
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF  
exposure, users can obtain Canadian information on RF exposure and compliance.  
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may  
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  
undesired operation.  
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the  
users authority to operate the equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada  
Q D ID :B 0 1 8 83 4  
 
iDM8  
Table of Contents  
Meet Your iDM8 ........................................................................................................... 1-2  
Charging the Unit.............................................................................................................3  
Using Bluetooth:Pairing Your Device.....................................................................................4  
Playing Audio Via Bluetooth................................................................................................5  
Playing Audio Via Aux.......................................................................................................6  
Internal Rechargeable Lithium-ion Battery...............................................................................7  
Consumer Product Safety Guide....................................................................................... 8-9  
Troubleshooting..............................................................................................................10  
Warranty......................................................................................................................11  
 
iDM8  
Meet Your iDM8  
Left Side  
Right Side  
Power/Charging/Pairing  
Indicator Light  
Power  
Volume Down  
Button  
Volume Up  
Button  
Play/Pause/Pairing  
Button  
Button  
Back  
Bottom  
Micro USB Charging Port  
Lock/Aux/Bluetooth Switch  
1
 
Using the  
iDM8  
Charging the Unit  
1.Connect the micro USB plug to the micro USB  
charging port on the back of the unit.  
2.Connect the standard USB plug end of the  
cable to a power USB port on a computer  
or other USB charging device. For first time  
use, charge unit for about 8 hours.  
3.A green light flashes while the unit is  
charging and glows steadily when unit is  
fully charged. If unit is not  
powered on when micro USB plug is  
connected, the green light flashes once to  
indicate unit is charging.  
USB 2.0  
NOTE: When unit is on and not connected  
to power source, flashing green light  
indicates battery needs charging.  
 
3
Using the  
iDM8  
Using Bluetooth: Pairing Your Device  
NOTE: See the iDM8 Bluetooth Connection Guide for complete pairing details.  
1. Move the Lock/Aux/Bluetooth Switch to the Bluetooth position (right).  
2. Turn on Bluetooth capability on your device and make it discoverable (see your devices  
instructions to add or setup a Bluetooth device).  
3. To turn on the unit, press and hold the Power Button on the iDM8 until an amber light  
flashes on front of the unit and it beeps twice to indicate auto-pairing attempt.  
4. Press and hold the Play/Pause/Pairing Button. The amber light will flash while the unit  
attempts to pair. On some devices, tap on the device name to begin pairing. If your device  
asks for a password, enter 1234 on the keyboard of your device. If no device is paired  
within 3 minutes, the unit will power off. If this occurs, retry steps 2-3.  
5. Once paired with a device, the amber light will glow steadily, then turn green. There  
should be an indication on your device that pairing is complete. On some devices, you  
must then select “Use as Audio Device (stereo)” or similar on the devices Bluetooth menu.  
Once paired, your device should link to the iDM8 whenever within range.  
 
4
Using the  
iDM8  
Playing Audio Via Bluetooth  
1. Move the Lock/Aux/Bluetooth Switch to the Bluetooth position (right) to listen to audio  
streamed wirelessly from your paired iPad, iPhone, iPod or other Bluetooth device.  
2. Press and hold the Power Button for 2 seconds to turn on the unit. The amber light will flash  
as the unit searches for a previously paired device, and then turn green when a previously  
paired device is detected.  
3. Press the Play/Pause/Pairing Button to play or pause audio from your Bluetooth device.  
NOTE: Play/Pause only works in Bluetooth mode. It does not control aux line-in devices.  
4. Use the Volume +/- Buttons to adjust volume.  
5. When done listening, press the Power Button to turn the unit off.  
5
 
Using the  
iDM8  
Playing Audio via Aux  
1. Move the Lock/Aux/Bluetooth Switch to the Aux position (center) to listen to audio via aux  
in.  
2. Connect the micro USB plug to the micro USB charging port on the back of the unit and  
connect the 3.5 mm audio plug to the headphone or line-out jack on your audio device.  
3. Power on the audio device and place in play mode.  
4. Press and hold the Power Button to turn on the unit (release when green light appears).  
5. Use the Volume +/- Buttons to adjust volume. You may wish to adjust the volume on your  
audio device, too.  
6. When done listening, press the Power Button to turn the unit off. Remember to turn off your  
audio device, too.  
6
 
Internal Rechargeable Lithium-ion Battery  
This device uses an internal rechargeable lithium-ion battery that should last the lifetime of the device. If you suspect your  
battery may be dead, try charging it several times. If the battery does not recharge, please contact us for repair information.  
WARNING/DISPOSAL OF UNIT  
Please do NOT attempt to change the battery yourself. If the battery has died and you do not want us to replace your battery,  
you should follow the disposal instructions below:  
Never dispose of used batteries/electronics with ordinary solid wastes, since they contain toxic substances.  
Always dispose of used batteries/electronics in accordance with the prevailing community regulations that apply to the  
disposal of batteries/electronics. If there are no local regulations concerning battery/electronics disposal, please dispose of  
the device in a waste bin for electronic devices.  
Many electronics retailers now recycle batteries and other electronic components at no charge. Check to see which ones in  
your area do so.  
CAUTION  
The battery used in this device may present a risk of fire, explosion or chemical burn if mistreated  
Never use or charge the battery if it appears to be leaking, discolored, deformed, or in any way abnormal.  
Never disassemble the unit or attempt to remove battery as that could cause leakage of alkaline solution or other electrolytic  
substance.  
Always confirm that the temperature is 5°C – 35° C (41° - 95° Fahrenheit) before you charge the battery. Leakage or  
deterioration of the battery may occur if this warning is not heeded.  
Never expose the battery to any liquid.  
Never expose the battery to excessive heat such as direct sunlight or fire. Never use the battery pack in an unventilated vehicle  
where excessive internal temperatures may be encountered.  
Always keep the battery out of the reach of infants and small children.  
7
 
Consumer Product Safety Guide  
IMPORTANT SAFETY INSTRUCTIONS  
When used in the directed manner, this unit has been designed and manufactured to ensure your  
personal safety. However, improper use can result in potential electrical shock or fire hazards. Please  
read all safety and operating instructions carefully before installation and use, and keep these instructions  
handy for future reference. Take special note of all warnings listed in these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub,  
washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its  
proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that  
may block ventilation openings. Also, it should not be placed in a built-in installation, such as a  
bookcase or cabinet, which may impede the flow of air through the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves  
or other appliances (including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in  
the operating instructions or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be  
walked on or pinched by items placed upon or against them. It is always best to have a clear  
area from where the cable exits the unit to where it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only using a warm damp cloth. Do not use solvents, etc.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not  
spilled into any openings or vents located on the product.  
8
 
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the  
antenna or cable system during a lightning storm or when it is left unattended and unused for long  
periods of time. This will prevent damage to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles  
as this can result in a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A. the power supply cable or plug has been damaged.  
B. objects have fallen into or liquid has been spilled into the enclosure.  
C.the unit has been exposed to rain.  
D. the unit has been dropped or the enclosure damaged.  
E. the unit exhibits a marked change in performance or does not operate normally.  
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month  
or longer, the power cable should be unplugged from the unit to prevent damage or corrosion.  
13. Servicing – The user should not attempt to service the unit beyond those methods described in the  
users operating instructions. Service methods not covered in the operating instructions should be  
referred to qualified service personnel.  
or call 1-800-288-2792 Toll Free  
9
 
Troubleshooting  
Unit doesn’t respond (no power)  
Make sure unit is completely charged. Check that all connections are  
correct and properly plugged in. Make sure your device is properly paired with the iDM8.  
Make sure the Lock/Aux/Bluetooth switch is not in the Lock (left) position  
(Lock disables all functions).  
Resetting the Unit  
If the unit does not respond properly or appears to be “frozen”, you may wish to try resetting it. To do  
so, move the Lock/Aux/Bluetooth Switch to the Bluetooth position (right), then press and hold the  
Play/Pause/Pairing Button and the Volume – Button simultaneously for about 8 seconds until a  
long beep sounds. Doing so will restore the unit to default settings. NOTE: After a reset, you will need  
to re-pair your Bluetooth device(s).  
Trouble pairing device/computer with iDM8  
Bluetooth implementation varies depending on your computers hardware and operating system. Please  
see our website for updates on pairing.  
• Make sure you have the latest firmware for your iPad, iPhone or iPod (update via iTunes if needed).  
• Make sure your device is working properly. Check your devices manual for details on Bluetooth  
pairing and linking.  
For further information and to see the latest instructions, visit www.ihomeaudio.com/support  
10  
 
Limited 90 Day Warranty  
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from  
defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.  
Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period,  
SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $15.00 charge for handling,  
packing, return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction upon delivery of  
this product to the Factory Service Center listed below. The product must include proof of purchase, including date of purchase. The  
fee for service without proof of purchase is $30.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective  
batteries are the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $15.00 ($30.00 without proof of purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Drive  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products  
which have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by  
unauthorized persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players,  
CDs or tape cassettes (if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original  
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members  
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or  
punitive damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these  
restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually  
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies  
product.  
© 2012 SDI Technologies, Inc. All rights reserved  
iDM8-010912-A  
Printed in China  
 

Grandstream Networks Telephone GXP Series User Manual
Grizzly Dust Collector T10252 User Manual
Hamilton Beach Iron 14010 User Manual
Harbor Freight Tools Nail Gun 95718 User Manual
Hasbro Games Monopoly Junior User Manual
Hearth and Home Technologies Patio Heater BODBAY User Manual
Heath Zenith Home Safety Product 5718 User Manual
HP Hewlett Packard Calculator 20B User Manual
Humminbird Fish Finder NS 10 User Manual
Husqvarna Cultivator DRT900 User Manual