iHome Stereo System IP39 User Manual

Model iP39  
FM stereo system  
with dual timers  
for iPhone and iPod  
 
Table of Contents  
Quick Start  
Controls and Indicators / iP39 Display  
Getting Started  
Connect AC adaptor, Install Clock Backup Battery, Install iPod/iPhone insert  
Setting Up the iP39  
1
2
3
4
Setting the Time and Calendar using IPhone/iPod Time Sync  
Setting Time and Calendar Manually  
Timer Operation  
Setting the Quick Timer, Setting Timer 2  
Using the Alarm  
4-5  
5
Setting the Alarm, Review, Arming and Disarming Alarm  
Resetting the Alarm to Come on the Next Day, Sure Alarm  
Charging your iPod/iPhone and USB Device  
Listening to iPod/iphone  
6
6
7
Listening to FM Radio  
Setting up the Antenna, Tuning and Playing the Radio  
Setting FM Radio Frequency/Range touse iP39 in Other Countries  
Using the Aux Line-In Jack with other Audio Devices  
A Consumer Guide to Product Safety  
Troubleshooting  
7
8
9
Maintenance  
Place the unit on a level surface away from sources of direct sunlight or excessive heat.  
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should be  
placed between it and the furniture.  
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner or similar  
materials can damage the surface of the unit.  
FCC Information  
This product bears the selective sorting symbol for waste electrical and electronic equipment  
(WEEE).  
This means that this product must be handled pursuant to European Directive 2002/96/EC in order  
to be recycled or dismantled to minimize its impact on the environment.  
For further information, please contact your local or regional authorities.  
Electronic products not included in the selective sorting process are potentially dangerous for the  
environment and human health due to the presence of hazardous substances.  
 
Controls and Indicators  
Reduce Volume Button  
Radio/Aux Button  
Play/Pause Button  
Back panel  
mo  
d
e
Timer Off  
Reverse Button  
Power Off/  
quic  
timer  
k
+1  
m
i
n
u
te  
Alarm Reset Button  
aux. in  
Aux-in Jack  
Quick Timer/  
Raise Volume Button  
Alarm Button  
+1 minute Button  
Time Sync/  
Time Set Button  
time  
sync  
time  
set  
Timer 2 Button  
-1  
dst  
+1  
DST Switch  
DC Jack  
Forward Button  
Backup Battery  
compartment  
USB  
charging  
USB Mode Switch  
USB Jack  
Dock  
FM Antenna  
iP39 Display  
PM Indicator  
Time Display  
Battery Low Indicator  
Timer2 Indicator  
Alarm Indicator  
Day/Timer 2/Sound/Radio mode Display  
Calendar/ Quick Timer/Alarm/Radio Station Frequency  
ON/OFF Display  
Quick Timer Indicator  
2
 
Getting Started  
Thank you for purchasing the iP39. Designed specifically to work with your iPhone and iPod, this system provides high quality  
audio performance that brings out the best in your music and lets you wake, sleep or even cook to it.  
Please read this instruction carefully before the appliance is operated and keep it for future reference.  
Connect AC Adaptor  
Connect the AC adaptor cable plug into the DC jack on the back of the system, then plug the AC adaptor into the wall outlet.  
Install Clock Backup Battery  
The iP39 uses a CR2032 battery for backup to provide continuous alarm operation and clock settings in the event of a power  
failure. If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the  
display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you  
must reset the time and alarm settings. The battery was included in the package with this instruction manual.  
1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement.  
2. Open the backup battery compartment door located on the rear of the unit.  
3. Insert a new CR2032 battery by easing it under the tabs in the battery well and pressing down. Make sure the side  
marked + is facing up. Close the compartment door.  
Note: The Icon is located at the left side of clock display. When battery is low and needs to be replaced, the “Battery  
Low”  
icon will flash.  
4. Close the compartment cover.  
Note: Make sure you dispose of battery properly (see your local regulations).  
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted,  
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries  
in a pocket, purse, or other container containing metal objects, mix with used or other  
battery types, or store with hazardous or combustible materials. Store in cool, dry,  
ventilated area. Follow applicable laws and regulations for transport and disposal.  
Install iPod/iPhone Inserts  
Your iP39 comes with a set of inserts to ensure your iPhone or iPod fits properly in the dock found at the foot of the system.  
To place an insert:  
1. Push dock drawer to access dock  
2. Select the insert for your iPhone/iPod (see table on page 1).  
3. Gently press the iPhone/iPod insert into the dock.  
4. Carefully place your iPhone/iPod into the dock. The iPhone/iPod must not be in a case or “skin”.  
5. To remove/replace an insert, first remove your iPhone/iPod then press down the insert latch, grip the insert and pull gently  
upwards.  
3
 
Setting Up the iP39  
Setting the Clock  
Setting the Time and Calendar using iPhone/iPod Time Sync  
Time sync mode allows you to sync the iP39 to the time and calendar from your iPhone or recent models of iPod like iPod  
Touch, iPod Nano and iPod Classic (older models such as iPod Mini do not support this feature).  
1. Make sure your iPhone or iPod is properly docked. Press the time sync/time set Button located at the back of the unit.  
“SYNC” will appear on the display, indicating sync function is in progrress.  
2. After sync is complete, the display will show the current time and date on your iPhone/iPod clock and two beeps will  
confirm time sync is done.  
3. If time sync fails, 2 second long beep sounds and the unit exits time sync mode. Try syncing agin, or set time and calendar  
manually (see below).  
NOTE: The iPhone is constantly updated to current time via cell phone towers. The time on your iPod is only accurate to  
the last time it was synced to a computer. Its possible to have up to 59 seconds difference between the iP39 and synced  
iPhone/iPod.  
Setting Time and Calendar Manually  
1. Set the DST Switch located on the back of the unit to +1 to add one hour or to -1 to subtract an hour to account for  
daylight saving time or standard time  
2. Press and hold the time sync/time set Button located at the back of the unit until the time display flashes.  
Press the  
or  
button to set the correct time (press and hold for rapid advance). Remember to set the correct AM  
or PM tme. The PM Indicator is located to the upper left side of the time digits; there is no AM indicator.  
3. Press the Alarm Button at any time during clock setting to toggle the display between 24 hour (military) and 12 hour  
(standard) display mode.  
4. Press the time sync/time set Button. The year will flash. Press the  
5. Press the time sync/time set Button. The date will flash. Press the  
and hold to enter fast scroll mode). The correct day will appear for the date set.  
or  
or  
button to set the current year.  
button to select the current date (press  
6. Press the time sync/time set again (or no button press within 10 seconds) to exit the clock setting mode.  
Timer Operation  
iP39 has 2 independent timers, a quick timer that lets you quickly set the timer in 1 minute steps and Timer 2, a normal  
timer which can be set in 5 minute increments. Both timers can run at the same time.  
Setting the timers  
1. Press the quick timer/+1 min button or the timer 2/ +5 min button to set the desired timer. Its icon and the timer digits  
will flash. Use the table below to set the desired countdown time in either timer mode while digits are flashing:  
RESULT  
ACTION  
Press  
Press  
Hold  
Press  
Hold  
BUTTON  
quick timer + 1 min  
timer 2 + 5 min  
quick timer or timer 2  
+ 1 minute each press  
+ 5 minute each press  
+ 1 hour each second held  
+/– 1 minute each press  
rapid scroll +/– minutes  
Press  
+/– 1 second each press  
rapid scroll +/– seconds  
Hold  
Cancel/end timer  
OFF  
Press  
4
 
Timer Operation  
1. When no button is pressed for 2 sec. the timer is set. The lower part of the display will show current timer time.  
2. Once the timer is set, it will start counting down over the set time period. Press the OFF Button at any time during timer  
setting to cancel the timer.  
3. When the set time is up, the buzzer alarm will sound until you press the OFF Button. Or press the quick timer/+1 min  
button or timer 2 +5 min button to add additional time  
Using the Alarm  
Setting the Alarm  
1. Press and hold the  
2. Press the or  
Alarm Button until the alarm icon and alarm time flashes on the lower part of the display.  
Button to set the desired alarm time. Remember to set the correct AM or PM alarm time (A or P next  
to alarm time indicates AM or PM alarm time).  
3. Press the Alarm Button to select wake to sound source. Press the  
iPod/iPhone, FM radio or buzzer. You cannot wake to aux audio device.  
4. Press the Alarm Button (or no button within 10 seconds) to exit alarm setting mode. The alarm will be armed,  
indicated by the alarm icon  
or  
Button to cycle through Alert Modes:  
Note: If iPod/iPhone or FM radio alarm sounds and iP39 detects no sound for 30 seconds (or if no iPod/iPhone is detected  
or if AC power is unpluged), the buzzer will sound instead and iPod/iPhone will power down.  
Review, Arming and Disarming Alarm (Turn Alarm Function On and Off)  
To review the current alarm time and arm the alarm or to disarm the alarm, just press the  
alarm is armed, the alarm icon and current alarm settings appear.  
Alarm Button as needed. If the  
Alarm Button to stop alarm  
Resetting the Alarm to Come on the Next Day  
When the alarm is sounding, press the Off Button to stop the alarm and cancel it. Press the  
and reset it to come on the following day at the same time.  
Sure Alarm  
The iP39 has a sure alarm feature. If you have installed the backup battery, the buzzer alarm will still sound in the event of  
power failure.  
 
5
Charging your iPod/iPhone and USB Device  
Note: Please make sure you are using the correct insert for your iPhone/iPod and that it is properly docked into the iP39.  
Failure to do so may damage your iPhone/iPod.  
While your iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged). Note  
that non-docking iPods will NOT charge.  
Charging a USB Device  
The iP39 is equipped with one USB 2.0 port (located on the the back apron) to charge  
RESET  
R E S E T  
T  
most USB compatible devices such as cell phones or PDAs while the iP39 is  
connected to AC power.  
To charge a USB-compatible device, lift the protective rubber cover from the USB port  
and insert the compatible USB charging cable (charging cable not included). Connect  
the other end to your device. Observe the charge indicator on your device to know  
when it is completely charged.  
NOTE: Some devices specifically require a computer-connected USB port to charge  
USB Mode Switch  
Note: A USB Mode Switch is located on the back of the unit near the USB port. The  
USB Mode Switch is to address USB devices that require different bias to charge  
properly.  
To use:  
1. Connect your USB device to the USB charge port on the rear of the unit. Watch your devices charge indicator. If it  
charges properly, allow it to charge.  
2. If the device does not charge, move the USB Mode Switch and again observe the devices charging indicator. If it charges  
properly, allow it to charge.  
If your device does not charge in either of the two USB switch positions, the device may require connection to a powered  
USB port on a computer.  
Listening to iPod/iPhone  
1. Press on the slide out dock to access the dock and place the insert for your iPhone or iPod model. Gently insert an  
already playing iPhone or iPod. The iP39 will automatically turn on and you will hear the music playing from your  
iPod/iPhone.  
Note: If the playing song/music loudness is too low on the iPod itself, the iP39 may not detect that the iPod/iPhone is in  
play mode. Press the  
Button to play it. If a timer is currently active, “iPod/iPhone” “on” will be displayed for 5 sec  
before returning to timer display. If no timers are active, “iPod/iPhone” “on” will be displayed while in “iPod/iPhone” mode.  
2. Press the or Button to change iPod/iPhone track forward/reverse.  
3. When the iPhone/iPod is docked and in standby mode, press the Button to play it.  
4. When the iPhone or iPod is in play mode, press the Button again to pause play; press again to resume it.  
5. Press the Volume or Button to adjust the iP39 volume.  
6. To turn off the unit, press the OFF button. Your iPhone/iPod will continue charging while in the dock.  
Note: While listening to iPod/iPhone, if iP39 has no power (AC adaptor not plugged in) the iPod/iPhone will POWER OFF.  
6
 
Listening to FM Radio  
Setting up the Antenna  
Extend the wire antenna fully for best reception. Do not strip, alter or attach to other antennas.  
Tuning and Playing the Radio  
1. Press the radio/aux. in Button as needed to turn on the iP39 and cycle to FM Radio mode. The middle part of the  
display will show “FM” and the lower part of the display will show the currently playing station frequency.  
2. Press the  
clear FM radio station. Holding  
3. Press the or Button to adjust volume setting.  
or  
Button to tune radio to a desired station. Press and hold the  
or  
Button briefly to seek the next  
or Button (2+seconds) will rapid scan as long as button is held.  
4. To turn off the unit, press the OFF Button. iPhone/iPod will continue charging while in the dock.  
Setting FM Radio Frequency/Range to Use iP39 in Other Countries  
Different regions of the world use different FM radio frequency steps and ranges. You will need to select the one that matches  
the standards in your region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is USA; if you live in the US,  
you may skip this section.  
1. Make sure the iP39 is OFF (not playing in any mode). Press and hold the Radio/aux Button for about 5 seconds until  
“FM” flashes in the lower part of the display. Press the  
AUS=Australia, CHN= China).  
or  
Button to select your region (EU=Europe, JPN= Japan,  
2. Press the Radio/aux Button again (or no button within 5 seconds) to exit the radio frequency setting mode.  
Using the Aux Line-In Jack with Other Audio Devices  
The iP39 has an aux line-in jack that lets you play other audio devices through it.  
1. Plug one end of a standard 3.5mm audio patch cord (not included) into the headphone or line-out jack on your audio  
device and the other end of the patch cord into the iP39 aux line-in Jack, located on the rear of the unit.  
2. Press the radio/aux. in Button until “AUX” appears in the middle part of the display, indicating aux mode is active.  
3. Turn on and play your device (device must be controlled independtly of the iP39).  
4. Press the Volume  
or  
Button to adjust the system volume. Adjust the output volume on your device if needed.  
5. To turn off the unit, press the OFF Button. Please remember to turn off your device, too.  
Using Dimmer  
1. When unit is not in an audio (radio, iPod or aux) or setting mode, press the or Button to adjust LCD backlight bright-  
ness.  
 
7
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to assure your personal safety.  
However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating  
instructions carefully before installation and use. Keep these instructions handy for future reference. Take special  
note, and adhere to all warnings on the unit and in the instruction and service manual.  
1. Water and Moisture – The unit should not be used near water. For example, near a bathtub, washbowl,  
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper  
ventilation. For example, it should not be situated on a bed, sofa, rug, or similar surface that may block the  
ventilation openings; or placed in a built-in installation, such as bookcase or cabinet that may impede the flow of  
air through the ventilation openings.  
3. Heat – The unit should be situated away from heat source such as radiators, heat register, stoves, or other  
appliances (including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating  
instructions or as marked on the appliance.  
5. Power Cord Protection – Power supply cord should be routed so that they are not likely to be walked on or  
pinched by items placed upon or against them. It is always best to have a clear area from where the cord exits  
the unit to where it is plugged into an AC outlet.  
6. Cleaning – The unit should be cleaned only as recommended by the manufacturer.  
7. Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the  
enclosure through openings.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall outlet and disconnect the antenna or  
cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will  
prevent damage to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can  
result in a risk of fire or electric shock.  
11. Damage Requiring Service – The appliance should be serviced by qualified service personnel when:  
A. The power-supply cord or plug has been damaged.  
B. Objects have fallen into or liquid has been spilled into the enclosure.  
C. The unit has been exposed to rain.  
D. The unit has been dropped or the enclosure damaged.  
E. The unit exhibits a marked change in performance or does not operate normally.  
12. Antenna – Do not connect an external antenna to the unit (other than that provided).  
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer,  
the power cord should be unplugged and take out batteries from the unit to prevent damage or corrosion.  
14. Servicing – The user should not attempt to service the unit beyond that described in the users operating  
instructions. All other servicing should be referred to qualified service personnel.  
8
 
Troubleshooting  
Symptom  
Possible Problem  
Solution  
Unit doesn’t  
respond  
AC adaptor isn’t plugged to a wall  
outlet or the connector is not plugged  
into the power supply jack o the back  
of the unit  
Plug the AC adaptor into a wall outlet and plug the connector into  
the supply jack on the unit  
(no power)  
Plug another device into a wall outlet (same outlet) to confirm the  
outlet is working  
Wall outlet is not functioning  
Using no or wrong iPod/iPhone insert  
iPod/iPhone is obstructed  
Make sure the dock insert is the proper fit to your iPod/iPhone  
iPod/iPhone does  
not dock properly  
Remove your iPod/iPhone from the dock and check for obstruction  
on the connectors in the dock and on your iPod. Then reseat it in  
the dock.  
Remove your iPod/iPhone from the dock and check for obstruction  
on the connectors in the dock and on your iPod. Then reseat it in  
the dock.  
iPod/iPhone is not docked properly  
iPod/iPhone does  
not respond to the  
unit  
Your iPod/iPhone software is too old  
iPod/iPhone is locked up  
Upgrade software on your iPod/iPhone via iTunes  
Please make sure your iPod/iPhone is working properly before dock  
into the unit. Please refer to your iPod manual for detail.  
Using 3rd generation iPod  
iP39 doesn’t support 3rd generation iPod  
Remove your iPod/iPhone from the dock and check for obstruction  
on the connectors in the dock and on your iPod/iPhone. Then  
reseat it in the dock.  
iPod/iPhone is not docked properly  
iPod/iPhone didn’t  
charge up  
iPod/iPhone is locked up/frozen  
Please make sure your iPod/iPhone is working properly before dock  
into the unit. Please refer to your iPod manual for detail.  
iPod/iPhone battery has problem  
Volume level is set too high  
Decrease the volume.  
If iPod/iPhone original sound source is poor quality, distortion and  
noise are easily noticed with high-power speakers.  
Sound is distorted  
Sound source is distorted  
Try a different audio source such as a music CD via line-in.  
If you are using an iPod Shuffle or external sound source like older  
generation iPod, try reducing the output volume on the device itself.  
Also, try turning bass boost OFF.  
Remote control  
doesn’t work  
Battery is weak or dead  
Replace with new battery  
Point the Remote Control toward the unit IR window, use within 10  
feet of the unit.  
Remote Control is not pointed toward  
the IR window  
9
 
© 2010 SDI Technologies, Inc. All rights reserved  
UKiP39-041610-0  
Printed in China  
 

Graco Inc Pressure Washer 1235 User Manual
Grandstream Networks Cordless Telephone HandyTone 488 User Manual
Haier Clothes Dryer HLP140E User Manual
Hamilton Beach Slow Cooker 840161800 User Manual
Harbor Freight Tools Air Compressor 94734 User Manual
Harbor Freight Tools Nail Gun 98751 User Manual
Huawei Network Router HG630a User Manual
Husqvarna Trimmer 322R User Manual
Impex Fitness Equipment PM 4400 User Manual
Impex Home Gym WM 357 User Manual