USER’S GUIDE
V:1319-0324-10
ID200B
DVD Player with Dock for iPod
fcc Warnings
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
additional Warnings
•
The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux écla-
boussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
•
Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the
apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facile-
ment accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débran-
chée du secteur.
•
Battery shall not be exposed to excessive heat such as sunshine,
fire or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
•
•
Caution marking is located at the rear of the apparatus.
Les marquages sont inscrits de derrière de l’appareil.
The marking information is located at the rear of apparatus.
Les précautions d’emploi sont inscrites de derrière de l’appareil.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B
3
dVd Player With dock for iPod
features
included
• Made for iPod
• Remote control: requires 2 AAA
batteries (not included)
• DVD player: DVD, DVD±R/RW
• CD player: CD, CD-R/RW, JPEG CD
• Progressive scan
• Audio/video cable
• NTSC/PAL
• On-screen display for iPod and DVD
• Supports Universal docking brackets
• Basic iPod controls from remote
• Composite video output
• Component video output
• Coaxial digital audio output
• Remote control
• Soft eject iPod docking drawer
• AC power: built-in AC power cable
4
iLive | ID200B
taBle of contents
introduction
6
8
setuP
Basic teleVision connection
adVanced teleVision connection
iPod
9
10
11
12
13
14
16
dVd and cd
setuP menu
softWare uPdates
comPany information
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B
5
introduction
PoWer
disc draWer
Press to turn the DVD
player off and on.
oPen/close
OPEN/
CLOSE
iPod docking drawer
Press to open and close.
DVD
/
CD PLAYER
STOP
POWER
PLAY/PAUSE
SOURCE
Play/Pause
stoP
source
Press to play or pause a Press to stop a CD, DVD, Press to switch between
DVD, CD, or iPod.
or iPod during play.
CD/DVD and iPod
mode.
comPonent Video
outPut
comPosite Video
outPut
Y
Pb/Cb
Pr/Cr
120V
~
60Hz
VIDEO
L
R
COAXIAL
DIGITAL
AUDIO OUT
VIDEO OUT
stereo audio
outPut
coaXial digital
audio outPut
ac PoWer
6
iLive | ID200B
PoWer
Press to power the DVD
player off or on.
oPen/close
Press to open or close the
DISC DRAWER.
OPEN/
CLOSE
mute
Press to mute the volume.
MUTE
SUBTITLE
ANGLE
PROG
suBtitle
Press to cycle through the
available subtitle options.
1
4
2
5
3
6
numBer keyPad
angle
Press to activate the angle
feature on supported DVDs.
goto
Press the GOTO button to
search for a specific title
chapter or time.
7
8
9
Prog
Press to program a loaded
disc to play tracks or chap-
ters in a specified order.
GOTO
disPlay
Press to view the on-screen
display.
10/0
10+
SHUFFLE
AUDIO
DISPLAY
audio
Press to cycle through the
available audio options.
shuffle
Press to play iPod in a
random order.
SETUP
ZOOM
setuP
Press to access the setup
menu.
Zoom
Press repeatedly to zoom in
and out on the loaded DVD.
ENTER
title
Press to access the loaded
DVD’s title menu.
directional/enter
TITLE
MENU
menu
Press to access the loaded
DVD’s menu.
n/P
Press to switch between
NTSC and PAL.
N/P
SOURCE
source
Press to switch between
CD/DVD and iPod mode.
f.BWd/f.fWd
Press and hold to fast
forward or rewind a loaded
disc.
PreV/neXt
Press to skip between
chapters or tracks.
rePeat
Press to repeat a single
chapter or track, or and
entire disc.
Play/Pause
Press to play or pause a CD,
DVD, or iPod.
REPEAT
STEP
A-B
L/R
SLOW CLEAR
VOL
steP
With a DVD paused, press
repeatedly to step through
the DVD one frame at a
time.
stoP
Press to stop a CD, DVD, or
iPod during play.
l/r
Press to switch the audio
channel.
a-B
Press to repeat a specified
section of a loaded DVD.
Volume
Press to adjust the volume.
sloW
Press to play the loaded
DVD in slow motion.
clear
Press to delete numbers
typed in using the number
keypad.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B
7
setuP
Power
Plug the attached AC cord into a
standard AC power outlet to power the
home theater system.
remote
Requires 2 AAA batteries (not included)
8
iLive | ID200B
Basic teleVision connection
composite Video output
Y
Pb/Cb
Pr/Cr
120V
~
60Hz
VIDEO
L
R
COAXIAL
DIGITAL
1 Plug the included RCA audio/video
cable into the comPosite Video
outPut (yellow) on the DVD player
and the composite video input
(yellow) on a television.
AUDIO OUT
VIDEO OUT
AUDIO INPUT
VIDEO INPUT
2 Plug the remaining plugs on the
included RCA audio/video cable into
the rca stereo audio outPuts
(red and white) on the DVD player
and the RCA stereo audio inputs (red
and white) on a television.
TELEVISION
3 Adjust the television’s input setting
to correspond to the inputs used
when connecting the DVD player.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B
9
adVanced teleVision connection
component Video output
TELEVISION
Requires a component video cable (not
included).
COMPONENT VIDEO INPUTS
1 Plug a component video cable into
the comPonent Video outPuts
(green, blue, red) on the DVD player
and the component video input
(green, blue, red) on a television.
Y
Pb/Cb
Pr/Cr
120V
~
60Hz
VIDEO
L
R
COAXIAL
DIGITAL
AUDIO OUT
VIDEO OUT
2 Plug the included RCA audio/video
cable into the rca stereo audio
outPuts (red and white) on the
DVD player and the RCA stereo
audio inputs (red and white) on a
television.
Y
Pb/Cb
Pr/Cr
120V
~
60Hz
VIDEO
L
R
COAXIAL
DIGITAL
AUDIO OUT
VIDEO OUT
AUDIO INPUT
3 Adjust the television’s input setting
to correspond to the inputs used
when connecting the DVD player.
TELEVISION
digital audio output
Y
Pb/Cb
Pr/Cr
120V
~
60Hz
VIDEO
L
R
COAXIAL
DIGITAL
Requires a coaxial digital audio cable
(not included).
AUDIO OUT
VIDEO OUT
1 Plug a coaxial digital audio cable
into the coaXial digital audio
outPut (black) on the DVD player
and the coaxial digital audio input
(black) on a television or stereo
system.
COAXIAL DIGITAL
INPUT
STEREO SYSTEM
OR
TELEVISION
2 Adjust the television or stereo
system’s input setting to correspond
to the input used when connecting
the DVD player.
10 iLive | ID200B
iPod
tV interface
docking an iPod
1 When connected to a television, the
docked iPod can be controlled from
the on-screen display.
1 Press the face of the iPod docking
draWer.
2 Connect the iPod to the connector
2 Use the directional/enter
buttons to navigate and make
selections on the on-screen display.
inside the iPod docking draWer.
When the speaker is plugged in, using
AC power, the docked iPod will charge.
Playing an iPod
1 Follow the instructions for docking
an iPod.
2 Press the PoWer button to turn the
DVD player on.
3 Press the source button to switch
to iPod mode.
After switching to iPod mode,
“INITIALIZING” will appear on the TV
display if connected. Wait until the
display reads “CONNECT OK” before
moving on to step 4.
4 Use the directional/enter
buttons to navigate and make
selections on the on-screen display.
11
dVd and cd
Playing a dVd or cd
Playing a JPeg Photo cd
1 Connect the DVD player to a
television and press the PoWer
button to turn the DVD player on.
1 Press the source button to switch
to DVD mode.
2 Press the oPen/close button to
open the disc draWer.
3 Load a JPEG Photo CD into the disc
draWer, label side facing up, and
press the oPen/close button to
close the disc draWer.
4 Press the directional/enter
buttons to highlight and select
photos from the loaded JPEG CD.
2 Press the oPen/close button to
open the disc draWer.
3 Load a DVD or CD into the disc
draWer, label side facing up, and
press the oPen/close button to
close the disc draWer.
4 The loaded DVD or CD will begin
playing automatically. If it does not,
press the Play/Pause button.
Programming a dVd or cd
1 Follow the instructions for “Playing a
DVD or CD”.
2 Press the Prog button on the
remote.
3 Press the directional/enter
buttons to select a program memory
slot.
4 Add titles and chapters or tracks
to the program menu using the
numBer keyPad.
Titles and chapters or tracks will play
in the order they are added.
5 Press the Play/Pause button to
play the programmed DVD or CD.
6 To cancel the program, press the
oPen/close button to open the
disc drawer.
12 iLive | ID200B
setuP menu
accessing the dVd setup menu
To access the DVD setup menu, press
the setuP button on the remote.
dVd setup menu
TV SYSTEM
SCREEN SAVER
VIDEO
TV TYPE
DEFAULT
OSD LANGUAGE
AUDIO LANGUAGE
SUBTITLE LANGUAGE
MENU LANGUAGE
AUDIO OUTPUT
DOWNMIX
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B 13
softWare uPdates
overview
Just as Apple continues to update and improve it’s software and hardware, iLive
works to remain up-to-date with the latest offerings from Apple.
ID200B.
checking your dVd player’s current software
1. Power on DVD player.
2. Remove any CD or DVDs from the disc draWer.
3. Press “9735”using the numBer keyPad on the remote.
4. Your DVD player’s current software version will be listed after “Software data-
code”. Write down this number for reference.
the list of products.
6. Select DOWNLOADS, then compare your DVD player’s software datacode to
the code listed in the Firmware Update section. If your DVD player’s datacode
does not match the most recent firmware update, then your player can be
updated.
7. Press the oPen/close button on the DVD player to exit the software menu.
WARNING: Do not adjust the region code on the DVD player. Changing the region
code can result in issues with your DVD player’s ability to read DVDs.
14 iLive | ID200B
Preparation
You will need all of the following.
•
•
•
Computer connected to the Internet.
CD drive that is capable of reading and writing CD disk
Blank CD-R or CD-RW disc.
creating a firmware disk
the list of products.
2. Select DOWNLOADS, then click on the most recent firmware update and save
file to your computer.
3. Load a blank CD into a CD writable drive.
4. Copy and Paste or Drag and Drop firmware file to CD drive, and write (burn)
file to CD.
installing updates
1. Power on DVD player.
2. Press the oPen/close button to open the disc draWer. Insert the firm-
ware disc. Press the oPen/close button to close the disc draWer.
The DVD player will read disk and automatically begin update process. The up-
date process will take several minutes.
3. The DVD player will automatically power off when the update is complete.
4. Once update is complete, power on the DVD player and remove update disk.
5. Press the setuP button to access the system setup menu.
6. Select “Default Reset” and press the enter button.
7. Your DVD player is now updated.
The following events may cause the writing of the firmware update to the player to be halted and the
player to no longer operate properly.
•
•
•
•
DO NOT unplug the power cord during the firmware update process.
Avoid loss or interruption of power during the firmware update process.
DO NOT press the power button on the unit during the firmware update process.
Check the firmware update disc for dirt or scratches before beginning the firmware update process.
CUstOmeR HeLPLINe | 1-314-621-2881
iLive | ID200B 15
comPany information
green initiative
environmental Commitment to ‘Protect for
today and sustain for tomorrow’
2009 marks the official launch of DPI, Inc.’s
corporate campaign for a greener and cleaner
world. DPI and its four brands, iLive, WeatherX,
Capri, and GPX, are building upon environmental
initiatives introduced at all of their facilities to help
formulate and sustain significant and important
conservation efforts within its manufacturing and
marketing communities. In addition to targeting
and selecting energy efficient product features, and
structuring ‘green office’ procedures, other initial
program efforts include:
•
•
Reduction of all packaging sizes
Recyclable plastics for clamshell packages,
with a plan to eventually replace plastic with
recyclable paper
•
•
Recycled fiber board in place of the polyfoam in
packing boxes
Recycled plastics in place of the virgin material
in product construction
international support
To download this User’s Guide in English,
Spanish, or French, visit the support section at
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda en
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section de
contact information
Address: 2116 Carr Street, St. Louis MO, 63106
Phone: 1-314-621-2881
Fax: 1-314-588-1805
Email: [email protected]
Parts Email: [email protected]
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are
subject to change without notice
|