Haier Washer HM1200TX User Manual

HM1400TX HM1200TX  
 
FUNCTION INTRODUCTION  
FUNCTION COMPARING TABLE  
MODE  
HM1400TX  
HM1200TX  
5Kg  
FUNCTION  
5Kg  
Washing capacity  
Programmes  
Cotton  
18  
18  
Synthetic  
Wool  
Adjustable thermostat(0~90 C)  
Cold wash button  
Speed button  
Economic button  
1400r/min  
1200r/min  
Spin speed  
Power switch  
ON/OFF  
Rinse  
Stainless steel tub  
Door-locking device  
Power  
300W  
700W  
300W  
700W  
Power(Wash)  
Power(Spin)  
Weight  
72Kg  
72Kg  
HXWXD  
 
HM1400TX HM1200TX  
 
Installation  
Unpacking  
levelling and  
positioning  
Remove the package and check that the machine is  
undamaged.  
If you have any doubts, do not use the machine and call on  
a qualified technician. Keep all packing parts (plastic bag,  
foam rubber, screws etc.) out of the reach of children  
sincetheycouldbedangerous.  
Important: The inside of the washing machine which  
consists of a floating unit, is fixed with screws at the back  
of the cabinet (Fig.1) during transport. Before starting the  
machine remember to release the floating unit by  
removing the above screws . To prevent water spray from  
entering the machine, remember to close the holes left  
open by the screws with the plastic caps provided in the  
packet containing the owner's manual. And rescrew the  
holes where the iron piece is taken down with the former  
two screws.Attention:keep the packing screws and plastic  
caps in a safe place for later use. It is important for the  
machine to be perfectly level (the angle of inclination on  
the work surface must not be more than 2 degrees). For  
this reason the machine is fitted with adjustable feet used  
for levelling the machine before use (Fig.2). In the case of  
flooring with carpeting, remember to check that the  
ventilation in the support area is not plugged.  
Fig.2  
Fig.1  
 
Installation  
Connect the plug to a socket provided with efficient  
Electric  
connectio  
earthing. Or use the spare earthing wire supplied  
together with the machine and the earthing terminal  
located on the left-upper corner of the back of your  
machine (Warning: this appliance must be earthed as a  
safety measure according to the law). Make sure that  
the voltage and frequency available correspond with  
the values stated on the data plate located at the back of  
the machine and that the electric system is  
dimensioned to withstand the maximum current shown  
on the data plate. If the socket the machine is  
connected to does not correspond with the plug,  
replace the plug with a suitable one and avoid using  
adaptors or shunts since they could cause overheating  
and burn out.The spare eathing wire is absolutely not  
allowed to be connected to water pipe,heating pipe or  
other kinds of pipes.  
Connection  
of tap and  
Loading  
Hose  
Connect the inlet hose to a cold water tap with a 3/4  
gas threaded opening, and fit the filter and the rubber  
gasket supplied with the washing machine. Check that  
it is tightly screwed to the tap (Fig. 3).  
Fig. 3  
If the water piping is new or has not been used for a  
long time, before making the connection, let the water  
run until it is clear and free from impurities.  
This step is necessary to ensure that the incoming  
water does not clog and possibly damage the machine.  
 
Installation  
Connection of  
the Drain Hose  
Connect the drain hose to a drain duct (with  
internal diameter of at least 4 cm.) or place it for  
drainage into a sink or a tub, ensuring that there  
are no kinks or bends. The free end must be at a  
height of between 80 and 100 cm. Should it be  
necessary to fix the end of the hose at a height of  
less than 80 cm from the floor, the hose must be  
fixed in the appropriate hook on the upper part of  
the back panel (Fig.4) or use the supplied  
supporttofixthedrainhose.(Fig.5)  
Fig.5  
Fig.4  
Insert stainless steel screen washers into end of  
each supply hose and attach that end of supply  
hose to your 3/4" water tap spigot.Be sure that  
youmatchupcold waterto"C".  
Connecting  
WaterSupply  
Note:Home Centers also have"Y" connectors  
and "Couplings" which enable you to connect  
the machine to your sinks faucet.  
 
Close up  
HM1400TX  
V
1
IV  
2
III  
3
4
II  
I
5
F
E
6
D
500  
C
7
B
A
1400  
HM1200TX  
V
1
IV  
2
III  
3
4
II  
I
5
F
E
500  
6
D
1200  
C
7
B
A
 
Close up  
A Programme selector lcwob.  
By turning this dial (clockwise only) you can  
select from eighteen wash programmes the  
onemostsuitedforyourwashing.  
1~7cottoncycle  
V
1
2
IV  
III  
3
4
II  
I
5
F
E
A~Fsyntheticcycle  
I~V wool cycle  
6
D
C
7
B
A
B Programme selector Knob.  
With this dial you can set the wash  
temperature that you desire.For synthetic and  
wool, the thermostat works below 60C and  
40C respectively.  
When the dial is located at " ", a cold wash is  
available  
C PowerLight  
This light indicates whether the electricity is on  
or off. The light comes on when button D is  
pressed and goes off when button D is not  
pressed.  
D ON/OFFButton  
ON/OFF button. Supplies electrical power to  
the machine.  
 
Close up  
E EconomicWashButton.  
It reduces water and power consumption when  
rinsingifthemachinedoesnothaveafullload.  
(Lessthan3kg)  
F1 Speed Button.  
500  
Push the button down, to reduce spin speed  
from1400r/min to 500r/min during strong washing  
modeandmediumwashingmode  
1400  
F2 Speed Button.  
500  
Push the button down, to reduce spin speed  
from1200r/min to 500r/min during strong washing  
modeandmediumwashingmode  
1200  
G Detergent Dispenser.  
The detergent dispenser is divided into 3 compart-  
mentsmarked1,2,3:(SeeFig.8)  
1Pre-washdetergent  
2Washdetergent  
3Softeners, conditioners, perfumes  
Fig.8  
H DoorLockLight  
Remember that only when the washer doesn't  
work,we can open the door. After the washing  
program finish,after 3 minutes, when the self-lock  
meterturnoff, wecanopenthedoor.  
 
Using instructions:Your machine  
offers the best results when...  
In order to get the excellent results that you would  
expect from your washing machine, it is important to  
load the washer correctly. You should therefore  
choose the quantity of each type of fabric that you want  
towash. Thistablewillhelp:  
The weight  
is right  
Colour fastfabrics  
Delicate fabrics  
Woollens  
maximum load 5kgs/11lbs  
maximum load 2kgs/2.5lbs  
maximum load 1kg/2.2lbs  
maximum load 2.5kgs/5.5lbs  
Mixed fabrics  
Laundry has  
been loaded  
correctly  
Divide the laundry by fabric and degree of soiling  
loaded making the loads as uniform as possible.  
Pull the handle out to open the door.  
Place the laundry in the machine remembering to  
arrangeuniformly.  
 
Using instructions:Your machine  
offers the best results when...  
The correct  
programme has  
been chosen  
A perfect wash depends above all on choosing the  
most suitable programme. We would therefore  
advise you to divide up your washing into separate  
loads of more or less the same types of fabric. This  
willmakeiteasiertoselectthebestprogramme.  
Hints on choosing the programme are shown in the  
tableonpagesofthismanual.  
Once you have selected a programme, just turn  
dial  
A clockwise until the chosen programme lines up  
withtheindicatorlineonthefaciapanel.  
When your machine is washing synthetic fabrics or  
woollens, the wash cycle stops before the last spin  
cycle, with the laundry soaked in water in order to  
prevent the formation of creases due to spinning.  
Complete the wash cycle with a spin cycle or  
simply drain the water from the washing machine  
withoutspinning.  
Anti-crease  
For the spin cycle, turn the selector knob A  
clockwisebyonestep.  
To drain, set the selector knob A on drain  
programme in both cases, before turning the knob  
AremembertoswitchOFFtheON/OFFbuttonD.  
 
Using instructions:Your machine  
offers the best results when...  
The detergent  
has been put  
in properly  
The 3 compartments marked 1, 2, 3 (Fig.9) should be  
usedasfollows:  
1Pre-washdetergent  
2Washdetergent  
3 Conditioner, starch, scents  
Fig.9  
Remember that it is important to use the right amount of  
soap powder or liquid for the type of laundry you are  
washing; the amount of detergent you use depends on a  
numberoffactors:  
Water hardness; if the water in your area has a  
high calcium content, we recommend using a  
anti-limestone additive.  
degree of dirtiness; increase the amount of  
soap powder used in the case of heavily soiled  
laundry.  
laundry load; the smaller the load the less soap  
powder you will need to use.  
 
Using instructions:Your machine  
offers the best results when...  
Thefollowingtablewillguideyou:  
Compart.1 Compart.2  
prewash  
Laundry  
Compart.3  
wash  
Normally 1/2 measuring 1 and 1/2  
Softeners  
soiled  
cup  
measuring (see note 3)  
cups  
When using concentrated detergents, remember to keep to  
the manufacturer's instructions using only the measuring  
cups supplied with the packet.  
Use more detergent in the case of very hard water ( more than  
21.F), but remember to maintain the proportion between the  
prewashandwashcycles.  
Liquiddetergent  
The liquid detergents currently available on the market may  
be used with the washing machine. Use compartment 2 for  
very dense liquid detergents. Follow the manufacturer's  
instructions when using liquid detergents sold with the ball  
detergent dispenser. Place the ball dispenser in the tub of  
washingmachinetogetherwiththelaundry.  
Theprewashcyclemaynotbeusedwithliquiddetergents.  
Note"3"  
For soft and fluffy laundry always a softener in the final rinsing  
cycle.  
Never place bleach in the other compartments.  
 
Using instructions:Your machine  
offers the best results when...  
You can now start washing. We would advise you,  
especially the first few times, to check that the  
programme that you have set is really the one you want  
and that the fabric selection is correct.  
The cycle is  
started  
If you want to start the cycle immediately, press the  
ON/OFF button D.  
At the end of the chosen cycie, the machine will stop  
automatically.  
The wash is  
finished  
Press the ON/OFF button D to switch off the power  
(lightCwillturnoff).  
 
Maintenance: five simple  
precautions for this machine  
Your machine is designed to last without complicated  
maintenance.  
All the same, we would ask you to take care of a few small  
matters. If you follow these four simple rules, we are sure  
that the washing machine will stay as your faithful friend and  
helperforalong, longtime.  
1. Ensure that your machine was installed according to the  
installation manual that comes with this booklet.  
2. Avoid at all costs using solvents either to clean the  
machine, or to do the wash. when clean the machine, cut  
offthepower.  
3. Clean the detergent dispenser every so often. This is very  
simple and should be done with water. Your machine has  
an extractable dispenser to make it even easier. Just pull  
it upwards and out.  
4. If it is long time no use, you'd better cut off the power,  
switch off the tap, and open the door to avoid unpleasant  
smell.  
5. Your washer is equipped with a self-cleaning pump. It is  
therefore not necessary to carry out cleaning and  
maintenanceoperations.  
Fig.8  
Open the cover of the filter, loosen the knob in counter-  
clockwise rotation, then take out the filter and clean it with  
water, everymonth.(seeFig.8)  
Note: Reassembly the filter carefully after cleaning,  
ensuring it is fit perfectly and no water can come out.  
 
Solution to Problems  
Even though your washing machine has been  
carefully designed and constructed, something could  
still go a miss with your machine. Before rushing to  
phone one of our service centres, however, please  
check that the operations listed below have been  
carried out. In many cases you will save time, money  
and bother. Our statistics show that many of the calls  
received by our service centres could have been  
avoidedwithjustalittlemoreattention.  
Checkthat:  
The washing  
machine  
won't start  
theplugispushedrightintothemainssocket;  
thedoorisclosedtightly:  
the "ON/OFF"buttonhasbeenpressed.  
Check that:  
the tap is open and properly connected to the inlet  
pipe;  
The washing  
machine won't  
fill with water  
The machine  
fills and drains  
continuously  
Checkthat:  
thedrainpipeisplacedatleast80cm/32inches  
The machine  
will not drain  
drain the water  
Checkthat:  
thedrainpipeisnotblocked;  
thedrainpipeisnotconnectedataheightmorethan  
1 metre/40inchesabovegroundlevel.  
There is too  
much foam in  
the tub  
Checkthat:  
thedetergentbeingusedismeantforautomatic  
machinesandnotforwashingbyhand;  
thattheamountusedisthatshowninthismanual  
and not more.  
 
Solution to Problems  
The machine  
Check that:  
vibrates too  
much when  
spinning  
the transit bolts have been removed (see  
installation manual);  
themachineislevel;  
thewashingloadisaccordingtotheinstructions  
given in thisbooklet.  
The machine  
stops operating  
before finishing  
Check that:  
thereisasuddenpowerfailureorwaterstop.  
themachineisinthenormalstateofrinse.  
 
Guide for selecting programme  
 
Warning:  
1. If the supply cord is damaged, it must be replaced, these are  
available from an authorised service agent.  
2. The appliance must be placed so that the plug is accessible.  
3. The appliance is to be connected to the water mains using new  
hose-sets, old hose-sets should not be reused.  
4. The appliance is not intended for use by yong children or infirm  
persons without supervision. Yong children should be supervised  
to ensure that they do not play with the appliance  
 
 
0020504683  
 

Graham Field Oxygen Equipment JB0160 010 User Manual
Grandstream Networks IP Phone GXP2010 User Manual
Grizzly Saw G7211 User Manual
Haier Air Conditioner HWR05XC9 User Manual
Honeywell Thermometer TH1100DV User Manual
Honeywell Thermostat CT70A User Manual
Hotpoint Oven SE1012X User Manual
Hotpoint Range RGB508PEAAD User Manual
Hotpoint Washer WWEF 722 User Manual
Hunter Fan Fan 20552 User Manual