Honeywell Scanner 1280i User Manual

Note: Refer to your user’s guide for information about cleaning your  
device.  
Connecting the Scanner  
RS232 Serial Port:  
When connecting the scanner, make sure the cable is pushed tightly  
into the scanner. Loosen the locking plate and slide it over the base  
of the cable connector to lock the cable in place. Tighten the screw.  
Getting Started  
Turn off computer’s power before connecting the scanner, then  
power up the computer once the scanner is fully connected.  
Power Supply Assembly (if included)  
Granit™ 1280i  
Industrial Full Range Laser Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Reading Techniques  
Note: The power supply must be ordered separately, if needed.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com  
日本: www.honeywellaidc.com をご覧ください。  
如要到中www.honeywellaidc.com简体。  
查看繁体版请登陆 www.honeywellaidc.com  
Standard Product Defaults  
The following bar code resets all standard product default settings.  
한글 www.honeywellaidc.com 로 이동합니다 .  
Standard Product Defaults  
1280-QS Rev A  
1/14  
Suffix  
Function Code Transmit  
Data Format Editor Instructions  
Programming Chart  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
When this selection is enabled and function codes are contained  
within the scanned data, the scanner transmits the function code to  
the terminal. Charts of these function codes are provided in your  
User’s Guide.  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
0
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
1
2
3
4
5
6
Add CR Suffix  
Enable  
(Default)  
Add Tab Suffix  
Disable  
Remove Suffix  
Enter Data Format  
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Clear All Data Formats  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Save  
Note: For a complete list of Code IDs, see the User’s Guide for your  
product at our website, www.honeywellaidc.com.  
7
 

Graco Car Seat 8485 User Manual
Graco Washer 309518P User Manual
Groupe SEB USA T FAL Iron FV5110 User Manual
Hafler Stereo Amplifier 1600 User Manual
Harbor Freight Tools Inflatable Bouncy Toy 95041 User Manual
Honeywell Stud Sensor C7089 User Manual
Hotpoint Ventilation Hood HD90X User Manual
HP Hewlett Packard Photo Printer 370 Series User Manual
Hypercom Scanner ICE 5500Plus User Manual
IBM Switch 8276 User Manual